Plastering Plaster Auto blocks wall rendering machine
Features
1. Our machine utilize the conveyor taking mortar forwardly and upwardly,It can plaster to the roof by all means(no leave 1mm).In this aspect our machine is unique.The conveyor can take mortar or stop in any position by hand control.
2. The spatula can change the angle at will,plastering the wall by rising large angle,sharpening and pressing by angle decline,thus guaranteed zero vertical error and plastering to the roof.
3. The hydraulic telescopic rod can make the machine installation in 10 second and the chassis is not stress.When you want to move the machine you just can release the rod as moving jack. The main rod declined by gravitation,the bottom life automatically.This kind of installation is the most fast and stable one.
4. The width of spatula is designed according the width of the door,The machine can go into the room freely.It can reach the inside corner and the exposed corner.
5. There are two min-vibrators after the spatula,thus you need not to worry about Hollowing and adhesion.
6. Our machine adopted the universal wheel after sealing and it can easily move to any place you like.
7. This machine is totally artificially designed.
8. The capacity is as 15 professional plasterers.
9. Saving more than 20% raw material (cement &sand)
10. Hydraulic lifting methods to improve the stability of the machine.
Safety Protection Designing
1. Before changing to the plastering angel,the startup switches of spatula is closed to avoid damage the spatula.
2. If the electrical machinery reverse,the machine can cut the power automatically to protect the wirerope from mass.Just commutate the two direction switch.
3. If the machine got stuck when declining,the power will be butting automatically to avoid wirerope came messy.
4. Due to long-term exposure,the wirerope may came rough.If the wirerope broken,the machineM would decline 20cm in abnormal speed and then it would be stuck.
5. All the active parts and tighten bolts have a high degree of anti-rust treatment.All the bearings have been multiple sealed up.All the accessories came form the best factory in China.
6. The front heavier design make the machine do not backward also if the hydraulic cylinder became flexible.
1. Introduction to our mortar rendering machine
The mortar rendering machines are also called mortar plastering machine, mortar leveling machine, mortar plaster machine etc. It is fully automatic rendering with perfect smooth rendering surface, no need manual leveling jobs. It saves labor cost, materials and time widely used for brick wall, cement wall, internal wall, house, workshop, house, building, skyscraper projects.
2.The main technical performance indicators.
| ITEM |
UNIT |
MODEL |
| |
|
GMEH-800-R |
GMEH-1000-R |
GMEH-800-G |
GMEH-1000-G |
| Rendering height |
m |
Standard 3.5
(Up to 5) |
Standard 3.5
(Up to 5) |
Standard
3.5 (Up to 5) |
Standard 3.5
(Up to 5) |
| Rendering width |
mm |
800 |
1000 |
800 |
1000 |
| Rendering thickness |
mm |
2-30 |
2-30 |
2-30 |
2-30 |
| Rendering speed |
m2/h |
30-60 |
40-80 |
30-60 |
40-80 |
| Voltage |
V |
380/220 (Customized) |
380/220
(Customized) |
380/220
(Customized) |
380/220
(Customized) |
| Lifting mode |
- |
By steel wire rope |
By steel wire rope |
By gear rack |
By gear rack |
| Main motor power |
Kw |
1.5 |
1.5 |
1.5 |
1.5 |
| Vibrating motor power |
Kw |
2*0.03 |
3*0.03 |
2*0.03 |
3*0.03 |
| Parts weight |
Kg |
50 |
60 |
80 |
90 |
| Machine weight |
Kg |
80 |
100 |
150 |
170 |
| Outer dimension |
mm |
1000×830×680 |
1150×830×680 |
1000×830×680 |
1150×830×680 |
3. Application
Brick Wall, Block Wall, Cement Wall, Internal Wall, House, Building, Skyscraper, Villa, Etc.
4. Applied materials
Cement, Gypsum, Lime, Ready Mix, Perlite, General Mortar, Insulation Mortar, Clay Mortar Or similar materials.
5. Comparison between machine and manual rendering.
| Comparison |
Rendering Machine |
Manual Rendering |
| Speed/8h |
500-750m2 |
less than 50m2 |
| Finishing |
smooth & flat with mirror finishing. |
always reveal crack, bubbles, etc. |
| Coating |
Once coating while render up and smooth down |
several times coating by numberless trowels |
| Procedures |
Automatic by machine |
adjust leveling by square bar again and again |
| Extra supporting |
electricity |
scaffolding, mop, trowel, square bar, lots of extra tools |
| Labor Intensity |
two workers. |
a lot more. Hard work. |
| Time Consumption |
saving 70% - 80% time |
long time work |
6.Packaging & Shipping
| PACKAGE |
In two seaworthy plywood boxes |
| CONTAINER NEEDED |
One 20'GP for 25 units or by LCL |
Features
1. Our machine utilize the conveyor taking mortar forwardly and upwardly,It can plaster to the roof by all means(no leave 1mm).In this aspect our machine is unique.The conveyor can take mortar or stop in any position by hand control.
2. The spatula can change the angle at will,plastering the wall by rising large angle,sharpening and pressing by angle decline,thus guaranteed zero vertical error and plastering to the roof.
3. The hydraulic telescopic rod can make the machine installation in 10 second and the chassis is not stress.When you want to move the machine you just can release the rod as moving jack. The main rod declined by gravitation,the bottom life automatically.This kind of installation is the most fast and stable one.
4. The width of spatula is designed according the width of the door,The machine can go into the room freely.It can reach the inside corner and the exposed corner.
5. There are two min-vibrators after the spatula,thus you need not to worry about Hollowing and adhesion.
6. Our machine adopted the universal wheel after sealing and it can easily move to any place you like.
7. This machine is totally artificially designed.
8. The capacity is as 15 professional plasterers.
9. Saving more than 20% raw material (cement &sand)
10. Hydraulic lifting methods to improve the stability of the machine.
Safety Protection Designing
1. Before changing to the plastering angel,the startup switches of spatula is closed to avoid damage the spatula.
2. If the electrical machinery reverse,the machine can cut the power automatically to protect the wirerope from mass.Just commutate the two direction switch.
3. If the machine got stuck when declining,the power will be butting automatically to avoid wirerope came messy.
4. Due to long-term exposure,the wirerope may came rough.If the wirerope broken,the machineM would decline 20cm in abnormal speed and then it would be stuck.
5. All the active parts and tighten bolts have a high degree of anti-rust treatment.All the bearings have been multiple sealed up.All the accessories came form the best factory in China.
6. The front heavier design make the machine do not backward also if the hydraulic cylinder became flexible.
){kind=link}